From professional translators, enterprises, web pages and freely available translation repositories.
Add a translation
mez kluzu
yield stress
Last Update: 2018-03-01 Usage Frequency: 6 Quality: Reference: Translated.com
mez kluzu,
yield point,
Last Update: 2014-11-21 Usage Frequency: 5 Quality: Reference: Translated.com
horní mez kluzu
upper yield point
Last Update: 2017-04-06 Usage Frequency: 3 Quality: Reference: Translated.com
mez kluzu (oceli)
flow limit
Last Update: 2019-10-08 Usage Frequency: 1 Quality: Reference: Translated.com
smluvní mez kluzu při 0,1 %
proof stress at 1,0
Last Update: 2017-04-06 Usage Frequency: 4 Quality: Reference: Translated.com
mez kluzu při nejvyšší pracovní teplotě
yield strength at maximum working temperature
Last Update: 2017-04-06 Usage Frequency: 2 Quality: Reference: Translated.com
smluvní mez kluzu při 0,2 % v ostatních případech.
the 0,2 % proof stress in other cases.
Last Update: 2013-08-16 Usage Frequency: 1 Quality: Reference: Translated.com
smluvní meze kluzu rp 0.2 nebo
or of the proof stress rp0,2,
\item{$f_y$} - mez kluzu (yield strength).
-
Last Update: 2018-02-13 Usage Frequency: 1 Quality: Reference: Translated.com
re/t, mez kluzu, označuje hodnotu při výpočtové teplotě:
re/t , yield limit, indicates the value at the calculation temperature of:
Last Update: 2014-11-21 Usage Frequency: 2 Quality: Reference: Translated.com
smluvní mez kluzu při 1,0 % u austenitických ocelí a nelegovaného hliníku,
the 1,0 % proof strength of austenitic steel and non-alloyed aluminium,
2.3 požadovaná bezpečnost šroubu na mezi kluzu.
2.3 desired safety of the bolt at the yield point.
v případě nelegovaného hliníku v nevytvrzeném stavu smluvní mez kluzu při 1 %.
for unalloyed aluminium in the unhardened state, the 1 % proof stress.
Last Update: 2016-12-09 Usage Frequency: 3 Quality: Reference: Translated.com
zjištěná hodnota meze kluzu nesmí být menší než re.
the value obtained for the yield stress must not be less than re.
horní mez kluzu musí být stanovena z tahového diagramu nebo jinou stejně přesnou metodou.
the upper yield point must be determined from the load/elongation diagram or by any other equally precise method.
rp 0,2 smluvní mez kluzu při 0,2 % zaručená výrobcem lahví v n/mm2;
rp 0,2 = conventional yield point 0,2 %, guaranteed by the manufacturer, in n/mm2;
horní meze kluzu reh v případě materiálu, který vykazuje horní a dolní mez kluzu, nebo
-of the upper yield point reh, for a material with both a lower and an upper yield point,
Last Update: 2016-10-05 Usage Frequency: 3 Quality: Reference: Translated.com
pokud ocel vykazuje dolní a horní mez kluzu, použije se hodnota: - rel, -
when a steel displays a lower and an upper yield point, the value to be taken is: - rel,
unionocel - plechy s vyšší mezí kluzu určené k tváření za studena
unionocel - sheets with a higher yield point to be cold-moulded
mez kluzu, případně smluvní mez kluzu při 0,2 %, resp. 1,0 %, při výpočtové teplotě,
yield strength, 0,2 % or 1,0 % proof strength as appropriate at calculation temperature,