Results for cmos translation from Chinese (Simplified) to English

互補性氧化金屬半導體 (cmos)
complementary metal oxide semiconductor

124 cmos 输入/输出
124 cmos inputs/outputs

检查处理器的主板上的 cmos 参数或跳线设置。
check the cmos parameters or jumpers settings on the motherboard for the processor.

使用 bios/cmos 设置工具来检查 bios。
if the operating system supports, try a step-by-step boot.

cmos i/o 端口: 75, 可选上拉电阻
cmos i/o ports: 75, selectable pull-up resistor

cmos i/o 端口: 75个，可选上拉电阻
cmos i/o ports: 75, selectable pull-up resistor

确保系统中 ram 缓存的配置正确（cmos 设置程序和主板上的跳线）。
make sure the system is configured properly (cmos setup program and jumpers on the motherboard) for the ram cache.

如果您听到 10 声蜂鸣，说明 cmos 关闭寄存器读/写错误
you are getting 10 beeps indicating cmos shutdown register read/write error

使用 bios/cmos 设置工具检查 bios 的设置，特别是内存设置。
check the bios using the bios/cmos setup utility, especially the memory settings.

使用 bios/cmos 设置实用程序检查 bios 的设置，特别是 ram 设置。
check the bios using the bios/cmos setup utility, especially the ram settings.

采用业界标准 cmos 工艺的高性能射频、模拟和混合信号电路设计采用业界标准 cmos 工艺的高性能射频、模拟和混合信号电路设计
high-performance radio frequency, analog and mixed-signal circuit design using industry-standard cmos processeshigh-performance radio frequency, analog and mixed-signal circuit design using industry-standard cmos processes

使用 <PROTECTED>/cmos 设置工具检查 <PROTECTED> 的设置，特别是启动顺序。确认您的系统能检测所有的驱动器并确认您试图启动的驱动器已列出。
update the system <PROTECTED> to the newest version. in addition, check to see if your system has a firmware that could also be updated to the newest version. refer to your motherboard documentation.

使用 bios/cmos 设置工具检查 bios 的设置，特别是启动顺序。确认您的系统能检测所有的驱动器并确认您试图启动的驱动器已列出。
update the system bios to the newest version. in addition, check to see if your system has a firmware that could also be updated to the newest version. refer to your motherboard documentation.

如果 bios 更新前未将 cmos 设置保存为自定义设置，请浏览屏幕上的每个选项，将 cmos 设置返回到更新 bios 之前记下的值。
if the settings were not saved as custom defaults prior to the bios update, go through each screen of options and return the cmos settings to the values that you wrote down prior to updating the bios.

按 [f9] 可将 cmos 设置恢复为出厂默认值，然后按 [enter] 可加载设置默认值。
return the cmos settings to the factory defaults by pressing [f9], then press [enter] to load setup defaults.

基于 dos 的接口允许您从参考系统解压缩 bios 设置，smbios 和 物料单 (bom) 信息到 ini 文件并且将该 ini 文件设置安装到目标系统。 当系统台式机主板拥有英特尔 945 或更高版本芯片组时，可编辑的标记过的设置也允许（且只能）解压缩和安装需要的 cmos 设置。
the dos-based interface allows you to extract bios settings, smbios and bill-of-material (bom) information from a reference system into an ini file and to also install the ini file settings onto target systems. editable tokenized settings also permit extracting and installing only the cmos settings that are needed when the system’s desktop board has an intel 945 or higher chipset.