Results for windows* 98se shutdo... translation from English to Chinese (Simplified)

windows* 98se shutdown problems
windows* 98se 关机问题

desktop boards - windows* 98se shutdown problems
台式机主板 - windows* 98se 关机问题

2 windows* 98se only
2 仅限 microsoft* windows* 98se

if you have windows* 98se, me or 2000:
如果您使用 windows* 98se、me 或 2000：

windows* me, windows* 98se, and windows* 98 users
windows* me、windows* 98se 和 windows* 98 用户

windows 98se and windows me fresh installation instructions
windows 98se 和 windows me 初次安装说明

drive not recognized during install of microsoft* windows* 98se or windows* me
在安装 microsoft* windows* 98se 或 windows* me 过程中，不能识别驱动器

first time installing sii raid driver with existing windows 98se/me
在现有的 windows 98se/me 中第一次安装 sii raid 驱动程序

this timing issue does not effect windows* 98se (second edition).
这个时钟问题不影响 windows* 98 se （第二版）。

after the system is restarted, windows* 98se or windows* me can be installed normally.
重新启动系统后，便可正常安装 windows* 98se 或 windows* me.

shutdown problem after installing usb 2.0 drivers
安装 usb 2.0 驱动程序之后的关机问题

resolves intermittent blue screen occurrences that can occur when installing the driver in microsoft* windows* 98se or windows* me
解决了在为 microsoft windows* 98se 或 windows* me 安装驱动程序时间歇蓝屏的产生。

verifying controller installation & using control panel utility (windows 98se/me)
验证控制器安装和使用 "控制面板实用程序" (windows 98se/me)

follow the normal windows 98se/me setup instructions to select your choice for partition and file system.
按照正常的 windows 98se/me 设置说明选择所希望的分区和文件系统。

desktop boards - shutdown problem after installing usb 2.0 drivers
台式机主板 - 安装 usb 2.0 驱动程序之后的关机问题

resolves an issue with raid1 mode while running microsoft windows* 98se or windows* me, whereby the serial-ata firmware incorrectly prompts the user to rebuild the raid1 array
解决了运行 microsoft windows* 98se 或 windows* me 时关于 raid1 模式的一个问题，该问题是serial-ata 固件不正确提示用户重建 raid1 阵列

if you have an existing windows 98se/me system you need to run the update program to install silicon image driver. the driver package is located in the silicon image driver diskette.
如果您已装有 windows 98se/me 系统，您需要运行更新程序安装 silicon image 驱动程序。驱动程序包位于 silicon image 驱动程序磁盘上。

wait until windows 98se/me finishes installing devices, regional settings, networking settings, components, and final set of tasks, reboot the system.
等待 windows 98se/me 完成安装设备、区域设置、网络设置、组件和一些最终任务，并重启系统。

put your windows 98se/me cd into the cd-rom/dvd drive, and the windows 98se/me boot diskette in the floppy drive if your system cannot boot from the cd.
把 windows 98se/me cd 插入 cd-rom/dvd 驱动器，如果系统不能从 cd启动，把 windows 98se/me 驱动磁盘插入软驱。

follow the instructions in this section if you are performing a new installation of windows 98se/me and you wish to boot from a device attached to the sii 3112 controller. you may start up the windows 98se/me installation from cd. if either your windows 98se/me cd or cd-rom drive is not bootable, you can user your start up floppy diskettes.
如果安装新的 windows 98se/me，并且希望从连接到 sii 3112 控制器的设备启动，则按照本节中的说明执行安装。可以从 cd 启动 windows 98se/me 安装。如果 windows 98se/me cd 或 cd-rom 驱动器不可启动，您可以使用启动软盘。