Je was op zoek naar: more than 1 signup per household (Bulgaars - Engels)

more than 4 colours, colours one page at a time
more than 4 colours, colours one page at a time

approximately 33% of their work requires more than 40 hours a week.
the median salary for employed qualified computer hardware engineers (2012) was $100,920 per year or $48.52 per hour.

note that the constant of proportionality between the signal and conjugate beams can be greater than 1.
note that the constant of proportionality between the signal and conjugate beams can be greater than 1.

more than 4,000 businesses as well as about 50 economic associations are currently members of aec.
more than 4 000 businesses as well as about 50 economic associations are currently members of aec.

aspin noted that in 11 years, the mda jerry lewis labor day telethons had raised more than $95 million for the muscular dystrophy associations.
lewis is also known as the host, for more than 40 years, of the muscular dystrophy association's annual labor day telethon and national chairman of the mda.

"when the governor of kaduna announced the introduction of sharia, although non-muslims form almost half of the population, violence erupted, leaving more than 1,000 people dead.
"when the governor of kaduna announced the introduction of sharia, although non-muslims form almost half of the population, violence erupted, leaving more than 1,000 people dead.

"the hollywood book of death: the bizarre, often sordid, passings of more than 125 american movie and tv idols".
"the hollywood book of death: the bizarre, often sordid, passings of more than 125 american movie and tv idols".

flushing there are times when you only want to flush the fluid manifold, such as: • breaks in spraying • overnight shutdown • end of potlife in this manual, that procedure is referred to as fluid manifold flushing. you can flush the fluid manifold by connecting a solvent pump to the fluid manifold. other times, you need to flush the entire system: • first time material is loaded into equipment* • color change • servicing • shutting down equipment for more than 3-1/2 hours (depends on material) • putting equipment into storage * some full system flushing steps are not necessary for initial flushing, as no material has been loaded into the system yet. to flush the entire system, you first follow the fluid manifold flushing procedure, at right, then the full system flushing procedure, page 18. fluid manifold flushing using solvent pump warning read warnings, page 5. • use the lowest possible pressure when flushing to avoid splashing. • before color change or shutdown for storage, flush at a higher flow rate and for a longer time. • a circulation setting is available. consult your distributor. refer to page 27. 1. follow pressure relief procedure, page 14. engage trigger lock. remove spray tip. 2. ensure that shutoff valves ga and gb are open. connect solvent pump line to solvent purge valve ja and jb. turn on solvent pump and open solvent purge valve ja. 3. adjust solvent pump regulator to desired pressure; use lowest pressure possible. ti1948a ti4699a jb
flushing there are times when you only want to flush the fluid manifold, such as: • breaks in spraying • overnight shutdown • end of potlife in this manual, that procedure is referred to as fluid manifold flushing. you can flush the fluid manifold by connecting a solvent pump to the fluid manifold. other times, you need to flush the entire system: • first time material is loaded into equipment* • color change • servicing • shutting down equipment for more than 3-1/2 hours (depends on material) • putting equipment into storage * some full system flushing steps are not necessary for initial flushing, as no material has been loaded into the system yet. to flush the entire system, you first follow the fluid manifold flushing procedure, at right, then the full system flushing procedure, page 18. fluid manifold flushing using solvent pump warning read warnings, page 5. • use the lowest possible pressure when flushing to avoid splashing. • before color change or shutdown for storage, flush at a higher flow rate and for a longer time. • a circulation setting is available. consult your distributor. refer to page 27. 1. follow pressure relief procedure, page 14. engage trigger lock. remove spray tip. 2. ensure that shutoff valves ga and gb are open. connect solvent pump line to solvent purge valve ja and jb. turn on solvent pump and open solvent purge valve ja. 3. adjust solvent pump regulator to desired pressure; use lowest pressure possible. ti1948a ti4699a jb ja ga gb flushing 309908g