Je was op zoek naar: elongation (Engels - Turks)

Engels

Vertalen

elongation

Vertalen

Turks

Vertalen
Vertalen

Vertaal onmiddellijk teksten, documenten en gesprekken met Lara

Nu vertalen

Menselijke bijdragen

Van professionele vertalers, bedrijven, webpagina's en gratis beschikbare vertaalbronnen.

Voeg een vertaling toe

Engels

Turks

Info

Engels

elongation

Turks

uzama

Laatste Update: 2017-02-14
Gebruiksfrequentie: 1
Kwaliteit:

Engels

cell elongation

Turks

hücre uzaması

Laatste Update: 2013-06-12
Gebruiksfrequentie: 1
Kwaliteit:

Engels

uniform elongation

Turks

tekdüze uzama

Laatste Update: 2017-02-14
Gebruiksfrequentie: 1
Kwaliteit:

Engels

elongation at fracture

Turks

kırılmada uzama

Laatste Update: 2017-02-14
Gebruiksfrequentie: 1
Kwaliteit:

Engels

elongation at break of aged

Turks

yaşlanmış kopma uzaması

Laatste Update: 2016-11-14
Gebruiksfrequentie: 1
Kwaliteit:

Engels

elongation at break of non aged

Turks

yaşlanmamış kopma uzaması

Laatste Update: 2016-11-14
Gebruiksfrequentie: 2
Kwaliteit:

Engels

resistant to shrinkage, elongation and all deformations caused by loads and design actions on the tunnel structure;

Turks

tünel yapısındaki yükler ve tasarım eylemleri nedeniyle oluşan büzülme, uzama ve tüm deformasyonlara dayanıklı olmak;

Laatste Update: 2017-12-02
Gebruiksfrequentie: 1
Kwaliteit:

Engels

breaking load, elongation and resistance tests shall be completed on the aluminum alloy catenaries conductor in accordance with the requirements of iec61089.

Turks

kopma yükü, uzama ve direnç testleri, iec61089 gereksinimleri doğrultusunda aluminyum alaşım katener iletkeni üzerinde tamamlanacaktır.

Laatste Update: 2016-11-13
Gebruiksfrequentie: 1
Kwaliteit:

Engels

the minimum tensile strength shall not be less than 14.5 mpa. and the minimum elongation at break shall be 200%.

Turks

minimum çekme dayanımı 14.5 mpa'dan daha az olmayacak ve kopma anındaki minimum uza % 200 olacaktır.

Laatste Update: 2016-11-13
Gebruiksfrequentie: 1
Kwaliteit:

Engels

tensile test (tensile strength, lower yield stress and elongation) (bs en 10002-1:

Turks

Çekme deneyi (Çekme dayanımı, alt akma gerilimi ve uzama) (bs en 10002-1:

Laatste Update: 2017-01-16
Gebruiksfrequentie: 1
Kwaliteit:

Engels

 sometimes, due to the very low stiffness of the supporting springs and the large value of the lift coefficient, elongation of the supporting system came to its maximum before the critical wind speed was reached.

Turks

 bazen, mesnet yaylarının çok düşük sertliği ve büyük kaldırma katsayısından dolayı mesnet sisteminin uzaması, kritik rüzgar hızına ulaşılmadan önce maksimum değere ulaşmıştır.

Laatste Update: 2017-01-15
Gebruiksfrequentie: 1
Kwaliteit:

Engels

the mechanical strength and other mechanical properties such as tensile strength, minimum elongation at break and physical/chemical properties shall also conform to the relevant clauses in iec 60502.

Turks

Çekme dayanımı, minimum kopma anındaki uzama ve fiziksel/kimyasla özellikler gibi mekanik dayanım ve diğer mekanik özellikler iec 60502 standardının ilgili maddelerine de uyacaktır.

Laatste Update: 2016-11-13
Gebruiksfrequentie: 1
Kwaliteit:

Engels

it has been shown that 7sk rna, a metazoan ncrna, acts as a negative regulator of the rna polymerase ii elongation factor p-tefb, and that this activity is influenced by stress response pathways.

Turks

7sk rna adlı bir metazoan ncrna türü, rna polimeraz ii uzama faktörü p-tefb'nin bir negatif düzenleyicisi olarak etki ettiği ve bu etkinliğin stres tepki yolağı ("stress response pathway") tarafından etkilendiği gösterilmiştir.

Laatste Update: 2016-03-03
Gebruiksfrequentie: 1
Kwaliteit:

Waarschuwing: Bevat onzichtbare HTML-opmaak

Engels

however, rope manufacturers give only the rope’s impact force "f0" and its static and dynamic elongations that are measured under standard uiaa fall conditions: a fall height "h0" of 2 x 2.3 m with an available rope length "l0" = 2.6m leads to a fall factor "f0" = "h0/l0" = 1.77 and a fall velocity "v0" = ("2gh0")1/2 = 9.5 m/s at the end of falling the distance "h0".

Turks

ancak, halat üreticileri sadece halat etkisine güç vermek için "f0" ve statik ve dinamik uzamaları standart altında ölçülür olduğunu uiaa esneme koşulları: düşme yüksekliği "h0" of 2 x 2.3m kullanılabilir halat uzunluğu ile "l0" = 2.6m esneme faktörüne yol açar "f0" = "h0/l0" = 1.77 ve düşme hızı "v0" = ("2gh0")1/2 = 9.5m/sn sonunda düşme mesafesi "h0".

Laatste Update: 2016-03-03
Gebruiksfrequentie: 1
Kwaliteit:

Waarschuwing: Bevat onzichtbare HTML-opmaak

Krijg een betere vertaling met
10,200,247,462 menselijke bijdragen

Gebruikers vragen nu voor assistentie



Wij gebruiken cookies om u de best mogelijke ervaring op onze website te bieden. Door de website verder te gebruiken, geeft u toestemming voor het gebruik van cookies. Klik hier voor meer informatie. OK